Main Squeeze Insert Replacement: Swap and Clean Guide

Why You Might Need to Replace Your Main Squeeze Insert

Over time, the insert of your Main Squeeze stroker can wear out or you might simply want a different texture. The Main Squeeze system is designed for easy insert swaps, so you can refresh your experience without buying a whole new stroker. This guide covers how to swap inserts safely and keep them clean for long-lasting use.

Inserts at a Glance

• Main Squeeze - The Virgin - Insert Replacement Vanilla: The Virgin insert is a replacement Ultraskyn insert with a realistic breaking hymen, measuring 7.5 in. insertable and 3 in. wide. Knowing the dimensions helps you confirm compatibility with your stroker case and ensures a proper fit.

  

• Main Squeeze - Katrina Jade - ULTRASKYN Stroker - Pussy Vanilla: The Katrina Jade ULTRASKYN stroker has a hard outer case, total length 9 in., insertable length 8.75 in., width 3.5 in., and is made of ABS, TPE, and ULTRASKYN. This shows the variety of insert sizes and materials available, which affects how you swap and clean them.

  

How to Swap Your Main Squeeze Insert

Swapping inserts is straightforward, but the exact steps depend on your stroker model. Based on the supplied information, here is the general process.

1. 1. Remove the old insert: Unscrew the end cap and top cap of the hard case. Gently pull out the existing ULTRASKYN sleeve. If it is stuck, run warm water over the case to loosen it.
2. 2. Prepare the new insert: Take your replacement insert, such as The Virgin, and rinse it with warm water to remove any packing residue. Do not use soap at this stage unless specified.
3. 3. Insert the new sleeve: Slide the new ULTRASKYN sleeve into the hard case, ensuring it is seated evenly. The open end should align with the top cap opening.
4. 4. Reassemble the case: Screw on the top and end caps. The end cap can twist to adjust suction strength, so set it to your preference.

Cleaning Your Main Squeeze Insert

Proper cleaning extends the life of your ULTRASKYN insert and keeps it hygienic. The supplied information does not include official cleaning instructions, but general care for similar materials applies.

1. 1. Disassemble the stroker: Remove the end cap and top cap, then take out the ULTRASKYN sleeve. This allows you to clean all parts thoroughly.
2. 2. Rinse with warm water: Hold the sleeve under warm running water to remove lubricant and debris. Avoid hot water, which can damage ULTRASKYN.
3. 3. Clean with mild soap: Use a small amount of mild, fragrance-free soap. Gently work it into the textured interior with your fingers. Rinse thoroughly until no soap remains.
4. 4. Dry completely: Pat the sleeve with a lint-free cloth or let it air dry on a clean towel. Do not use paper towels, which can leave fibers. Ensure it is fully dry before reassembling.
5. 5. Store properly: Place the clean, dry sleeve back into the hard case and screw on the caps. The double-cap design also serves as a discreet travel and storage case, keeping your insert fresh.

Important Considerations for ULTRASKYN Inserts

ULTRASKYN is a lifelike material that warms to the touch, but it is porous and requires gentle care. Avoid silicone-based lubricants with TPE/ULTRASKYN, as they can degrade the material. The supplied information does not confirm specific lubricant compatibility, so sticking to water-based lubricants is a safe choice. Also, do not boil or dishwasher-clean ULTRASKYN sleeves, as high heat can cause warping or melting.

What the Supplied Information Doesn't Confirm

• Main Squeeze - The Virgin - Insert Replacement Vanilla: The Virgin insert replacement does not include specific cleaning or swapping instructions in the supplied records. You may need to rely on general ULTRASKYN care guidelines or contact support for model-specific advice.
• Main Squeeze - Katrina Jade - ULTRASKYN Stroker - Pussy Vanilla: The Katrina Jade stroker's specifications mention it fully disassembles for cleaning, but no step-by-step cleaning method is provided. While disassembly is confirmed, the exact cleaning procedure is not documented, so the steps above are based on common practice for similar materials.